80 METER INVERTED-L INSTALLATION
INTERNATIONAL ANTENNA COMPANY
888-268-4214 CLICK HERE FOR PRINTABLE PDF
are the proud owner of the new DOUBLE BAZOOKA INVERTED-L ANTENNA. The
first thing to do is to consider how you want to mount the antenna. The
Inverted-L can be installed along the side of a tower or metal pole.
Also, the Inverted-L can be installed along the side of a tree or wooden
support. The antenna will have both horizontal and vertical radiation
components. The horizontal radiation pattern is generally broadside of
the horizontal wire section of the antenna. The vertical component of
the antenna tends to be omni directional. The feed point of the antenna
should be mounted approximately groundlevel in reference to the vertical
support (tower or tree).
When installing along side a metal
tower or metal pole the Inverted-L antennas vertical portion of the
antenna should be no closer than 24 inches. It is recommended that an
insulated support be secured to the base of the tower or pole.
If mounting to a tree or wooden pole the vertical section of the
Inverted-L antenna can be close to the vertical support but not touching
with no effect to performance.
At a point between 30-80 feet
above the “T” mold feed point connection install an insulated support
that will keep the antenna 24 inches away from the metal tower or
Install the vertical portion of the antenna first to
the bottom insulated support point then to the top support point. This
part of the antenna should be parallel and equally 24 inches from the support tower or pole.
NOTE: If mounting to a tree or wooden pole the vertical section of the Inverted-L antenna can be close to the vertical support but not touching with no effect to performance.
extend the horizontal section of the antenna outward and parallel to
the ground as much as possible for optimum results. The end may be
fastened with cord to a support pole or tree, using proper safety rules
in safeguarding that persons, pets, other objects cannot come in contact
with any of the elements as shock hazards or RF burns could result
Whenever connecting the end of the antenna to an object it is
recommended that a light or medium relief “springs” with a safe working
load limit of 5 lbs be installed to compensate for any movement of the
antenna or connecting object such as a tree. “DO NOT USE A TENSIONER
Next, install several quarter wavelength ground radials
to “T” mold ground connector. Also, install an approved electrical
code ground rod and secure to the ground connector.
mounting, the antenna connect a 50 ohm feed line such as RG-58, RG-8 or
RG-213 coax to the antenna and your transmitter. With a very low amount
of output power applied to the antenna at your desired frequency,
measure the SWR. An antenna analyzer may also be used to measure the
SWR. The antenna should exhibit an SWR of less than 2:1 across the
entire 80 meter band. The antenna is cut for the CW portion of each
band from the factory so further adjustment is optional. If the SWR is
higher than 2:1 be sure the antenna is well grounded to the ground
radials and ground rod. It is recommended that at least 4 or more
ground radials be installed at the base of the antenna.
lower the SWR, fold the 300-ohm twin lead back on itself ensuring it is
flat on itself with no gaps equally on each side and secure with
tywraps. The fold of 12, 24, 36 or 48 inches must be done in a (single
fold over not multiple fold overs). The loop you have created is the is
the tie off point. This procedure will raise the operating frequency of
the CW portion of the band. For more detail see tuning instructions on
the IAC website. If you measure a higher SWR, make sure that the antenna
is not near or
touching any metal objects such as rain gutters, aluminum siding, metal roofs etc.
DUE TO CERTAIN SOIL CONDITIONS A TUNER MAY BE REQUIRED TO LOWER THE SWR. APPROXIMATE
FOLDOVER FOR EACH SIDE OF THE 300-OHM ANTENNA END SECTIONS FOR CERTAIN FREQUENCIES:
1.8 MHz = (1.5 feet), 1.9 MHz = (4.0 feet), 2.0 MHz = (6.0 feet). Additional adjustment may be required.
making sure the SWR is within spec and everything is clear of the
antenna. You are ready to operate and enjoy all of the great signals
and DX contacts that this antenna offers. We at IAC wish you the
greatest DX' ing and are sure you will be pleased with your purchase.
IAC ACCEPTS NO LIABILITY FOR DAMAGE OR INJURY RESULTING FROM THE
INSTALLATION AND USE OF THIS ANTENNA.